2015-2018 Ford F-150 2wd/4wd 2" Rear Lowering Shackles - PRS-413710
The PRS-413710 2" rear lowering shackles for your 2015-2018 Ford F-150 2wd/4wd are a great way to bring the rear end of your F-150 to a nice level stance. These shackles give a 2" drop in the rear and do not require pinch weld modification. The drop shackles will get your 2015-2018 Ford F-150 truck sitting level in an hour or two, easily installed, and of better quality than the OE parts being replaced. Constructed of solid steel, urethane bushings, and powder coated in gunmetal, these give you the look you're after. These rear lowering shackles come with everything needed to get the job done right! Below you will find all of the specifics on these rear lowering shackles-
These Drop Shackles Include-
Part # PRS-413710
Posted by Dave C on
Only lowered rear an inch. Installed on 2018 F150 4x4 reg cab 6.5 bed with no miles, maybe it will settle when we drive it.
Posted by George M. on
The installation was easy. (be sure to remove the rear shackle spring bolts from both sides or else you will not be able to lower the springs enough to get the bolt past the frame). The actual drop was 1 inch at the rear wheel well with the 2 inch shackles on a 2WD 2016 Lariat super crew. The same result that I had on a 2008 F150 4X4 King Ranch. The look from the side is much better, just a very slight forward rake.
Posted by Phil LaMoreaux on
I'm happy with the quality and ease of installation. I did notice a new drivetrain vibration. These do change the pinion angle slightly. I will try a set of shims, but if the vibration persists, I will be returming to the stock height shackles.
Posted by Unknown on
Didn't level the truck but still looks better than stock. Did get rid of a lot of the suspension hop in the back which was a plus.
Posted by Gary N. on
I installed these on my 2016 F150 XL 2wd. The picture shows two sets of holes but the actual parts have only one set so they are not adjustable. I didn't measure at the wheel well but they lowered the truck by about 1.5" at the rear bumper. Unlike other kits that I've seen reviewed, I didn't need to do any cutting or bending on the bed support. The job took under 2 hours and I didn't have any problems. Very satisfied. You'll want to have a deep 24mm socket.
Posted by Tom on
I thought a 2 inch rear drop would level my 2016 Ford F150 limited 4x4 pickup. After measuring the rear it is still 3/4 inch higher. It still looks good! Definitely satisfied.
Posted by Unknown on
Gives the truck just enough drop in the back.
Posted by Scott looney on
I bought these to lower the rear of my 2016 f 150 4x4 and have to say was really concerned that they might not fit or that they would not level the truck like I wanted, however after spending about 30 minutes to install them I was more than pleased!
They were very easy to install, gave my truck the level look I Wanted and the brackets look the part of a quality made product.
Posted by david ferguson on
Installed the shackles last Saturday they were a perfect fit with a good finish on them . they came with predrilled holes and grease fittings just in case they do squeak . I am %100 satisfied .
Posted by Larry in OKC on
The customer service- The real test is when something goes wrong. The USPS box arrived with some clear tape from an in transit box break (not the shippers brown tape). I found an item missing. The same afternoon my box arrived, a replacement was shipped with only one question asked "would you send us a photo of the taped box", no other questions, no other charges!
The product- As good as I could expect. Welds were done well, paint finish good and zerk grease fittings to extend wear and reduce any noise. Great first time experience on this site, I did not have to be one of their top 10 buyers to get this level of service.
All prices are in USD